Leave a Reply

Your email address will not be published. Required fields are marked *

MOUNTAIN BIKE COLLECTION

ROAD BIKE COLLECTION

Myles Rockwell’s 1998 Cannondale Fulcrum

THE STORY

"Before the advent of platform valving in rear shocks, bicycle frame engineers went to all sorts of efforts to build pedaling efficiency directly into the suspension design. Few bikes exemplify those efforts better than the Cannondale Fulcrum DH used on the World Cup downhill circuit in 1998.

World Cup downhill racing was a different beast 17 years ago. The tracks were nearly twice as long as today’s shorter and more intense efforts, and there was significantly more pedaling required. Rear shocks were much more primitive in their internal designs, too, offering little to no help in terms of keeping the back ends from flailing about when racers had to put the power down.

The wide range of courses also required a similarly broad selection of chainrings, which posed yet another set of challenges for suspension engineers.

Cannondale was at the height of its glory days in the late 1990s and the company adopted an unquestionably radical approach to the problem at hand. Unwilling to accept the kinematic compromises of multiple chainring sizes, Cannondale instead developed a complex jackshaft drive system for the team-only Fulcrum DH frame that used the same chainring no matter what.

With the chainline now a constant, the suspension engineers then designed a short dual-link rear end with roughly 6in of travel and an axle path that trended rearward toward the end of the stroke.

The jackshaft system was unquestionably complex, requiring three separate chains, four additional cogs, an army of bolts and bearings, and even an eccentric bottom bracket borrowed from a tandem. Pedal power was transferred from the left crankarm through a short section of chain to a cog on the jackshaft. From there, another short chain ran from the right side of the jackshaft to a secondary chainring that was bolted to the primary chainring, which ultimately drove the rear wheel.

And since it was the left chainring that actually transferred rider torque – not the driveside one as usual – the one on the right side merely rotated about the bottom bracket spindle on a pair of sealed cartridge bearings.

“The goal was to have suspension that was the best you could make it but still have it pedal well,” said Doug Dalton, who currently works for SRAM but was the lead team mechanic on Cannondale's downhill program during the late 1990s. “That’s really why we had that whole drive system. It was just to make sure the rear suspension was optimized around a single, specific gear.”

The drive system wasn’t the only area of innovation, either.

Up front, Cannondale adapted its Headshok suspension fork into the dual-crown Moto DH, which used eight sets of needle bearings and square-profile stanchions to produce far more torsional stiffness than typical inverted fork designs. The oversized front end also featured interchangeable cups that allowed for adjustable head tube angle – more than 10 years before Cane Creek introduced its AngleSet.

Although effective, all of these innovations certainly had their downsides.

For one, changing gear ratios on the jackshaft system took even the seasoned team mechanics about 25 minutes. The needle bearings in the fork had a tendency to migrate, too, so they had to be ‘reset’ up to three times a day in order to restore the full travel.

Moreover, all that additional hardware made the bikes seriously heavy. Dalton said the bikes were nearly 23kg (50lb) in total – almost 7kg (15lb) heavier than top downhill racers today. Finally, the bikes were outrageously expensive to produce. Cannondale apparently never had any intention of actually bringing the Fulcrum DH to market – which would have helped offset the costs – and Dalton estimates that each one cost Cannondale between US$20,000 and US$30,000 to make (and that was in 1998).

It’s entirely possible that Cannondale might have refined the Fulcrum DH in later years. Unfortunately, the program was canceled after just two years.

“The next year, the World Cup went live on Eurosport so all of the tracks went down to around three-and-a- half to four-and-a-half minutes instead of the big, six-and-a-half minute Euro, big-dog shredding courses,” Dalton said. “That Fulcrum DH was designed for big, wide-open, amazing tracks. Now we were going into these shorter and faster tracks. That’s why the next year we went for similar travel but went as light as we could. That’s when Gemini was born.”

According to Dalton, Cannondale ultimately made less than a dozen Fulcrum DH machines in total, each of which is a stunning snapshot of how things used to be.

-James Huang // Bike Radar

 

BUILD SPEC

1998 Cannondale Fulcrum DH Myles Rockwell TPC Museum Build Spec

More from MTB Collection

More from Road Collection

Otis Guy’s 1978 Breezer Series 1 #2.81

1980 Ritchey “Pre Serial #”

1980 Breezer Series II #19

1982 Breezer Series III #32

1982 Salsa Scoboni #5

1982 Sweetheart Cycles Moto Cruiser

1983 Breezer Series III #43

1983 Ritchey “Faux Lugs” Competition

1983 Cunningham Indian #29

1983 Mantis Sherpa

1984 Moots Mountaineer

1984 Swift Mountain Bike

1985 Ibis Custom

1985 Velocitech Mountain Machine

1985 Mountain Goat Camoflage Deluxe

1985 Salsa Ala Carte

1985 Steve Potts Limited Edition

1985 Fisher Competition

Scot Nicol’s 1986 Ibis Trials Pro

1986 Ross Signature Team

1987 WTB Team Trek

1987 Klein Pinnacle “Kleiningham”

1987 Fat Chance Kicker

1987 Yeti Yak

1987 Rossin Max Concept

1987 Steve Potts Signature

1988 WTB Wildcat Prototype

Hank Barlow’s 1988 Merlin Ti

1988 Mongoose Tomac Signature

1988 Cunningham Racer 22C

1988 Cunningham Racer 24C

Russell Worley’s 1988 Yeti FRO

1988 Cunningham Racer 25C

1988 Mountain Goat Dinoflage Deluxe

Chris Herting’s 1988 Yeti FRO

1989 Mantis XCR

1989 Otis Guy Braunstein Quay Art of the MTB

1989 Salsa Moto

1989 Salsa Titanium Prototype Ala Carte

1989 Gecko Y-File

1989 Doug Bradbury Manitou

1990 Mountain Goat Yuppie Deluxe

1990 Mantis Valkyrie

1990 Doug Bradbury Manitou Mountain Bike

1990 Fat Chance Yo Eddy

1990 Koga-Miyata Ridgerunner Alloy

Juli Furtado’s 1990 Yeti FRO

Juli Furtado’s 1990 Yeti C-26

Juli Furtado’s 1991 Yeti ARC

1991 Doug Bradbury Manitou Mountain Bike

1991 Salsa Ala Carte Jelly Bean

1991 Yeti Tree Frog #2

Greg Herbold’s Titanium Miyata

1991 Yeti Ultimate

Travis Brown’s 1991 Manitou FS

1991 Klein Attitude Campagnolo

1991 Klein Dolomite Attitude

1992 Yeti Campagnolo Ultimate

1992 Specialized Epic Ultimate

Ned Overend’s 1992 Specialized M2

1992 Team Issued Slingshot

1992 Fat Chance Yo Eddy

1992 Clark-Kent Fat Bike

1992 Klein Gossamer Attitude

1993 Klein Team Storm Adroit

Matt Parker’s 1993 Yeti Ultimate XL

Tinker Juarez’s 1993 Team Storm Klein

Missy Giove’s 1993 Yeti ARC ASLT

1993 Raleigh Tomac Signature

Jacquie Phelan’s 1993 WTB Phoenix

1994 Merlin Newsboy

1994 Yeti ARC

Kurt Stockton’s 1995 Kamikazi Rubicon

Myles Rockwell’s 1998 Cannondale Fulcrum

Yeti C-26 – 20th Anniversary Special

Travis Brown’s 2000 Sydney Olympics Trek

Myles Rockwell’s 2000 Giant ATX One

Travis Brown’s 2004 Marathon Trek

Travis Brown’s 2007 Trek 69er